国产精品一区二区三区在线播放,国产高清免费一级一片视频播放 ,国产男女猛烈无遮挡免费视频,无码人妻一区二区三区免费手机

Online Service
Scan it
Support hotline
18681482740
Service Hotline:
18681482740
中文  |   English
News
Contact

Address: Floor 1, Building 2, Quanshengchang Industrial Park, Buyong Shajing Road, Shajing Street, Shenzhen

Contact: Mr. Li 18681482740

Email: lilinhan1314@126.com

Website: m.f4wow.cn

News
What should be paid special attention to in the design of antenna shrapnel
04-30 / 2024

What should be paid special attention to in the design of antenna shrapnel?




1、 Motherboard




1. When wiring associated with RF, special attention should be paid to using a 45 degree angle or arc treatment at turns, and ground paving protection and characteristic impedance simulation of wiring should be done well. In addition, the RF ground should be designed reasonably and effectively. The reference ground plane for RF wiring should be found correctly, and the signal return path should be ensured to be the shortest when RF signal wiring, and the corresponding layer between RF signal wires and ground should not be affected by other wiring. The boundary between the board and the ground should be marked with a "ground wall". The antenna feed microstrip line led from the RF control module of the PCB circuit board should not be placed in the middle layer of the PCB circuit board to prevent the characteristic impedance of the line from being uncontrollable and reduce losses. It is advisable to design it on the TOP surface, and the reference layer should be a complete reference plane. And at the junction with the shielding box, the shielding box should be designed with slots and bypasses to prevent short circuits and bypass coupling.




2. Protect the surrounding area of the RF control module from scattered unshielded parts, and minimize the opening of heat dissipation holes. The most taboo is the elongated hole groove. The projection area of the mobile phone antenna shrapnel has a complete ground pavement, and it is best not to distribute components on the antenna side, especially parts containing metal components, such as audio speakers, motor motors, camera substrates, and low-frequency drive components, to be grounded as much as possible. These have a significant negative impact on the electrical characteristics of antenna shrapnel




3. The spatial radiation of antenna shrapnel will be coupled and absorbed by the metal parts of the motherboard (including the metal component decorative parts around the antenna on the chassis), resulting in a certain amount of secondary radiation. The frequency is related to the size of the metal product. This can lead to a certain level of noise in the entire machine, which is also related to the series resonance pairing control circuit between the antenna and RF control module. If the stability performance of the series resonance pairing control circuit is poor, it is easy to excite disturbances that generate higher-order harmonics. Therefore, it is stipulated that such parts have good grounding to eliminate or reduce secondary radiation.




2、 Design of the casing




Because the built-in antenna shrapnel on a mobile phone is relatively sensitive to the conductive medium around it, the design of the phone shell is inevitably related to the antenna characteristics. The surface coating material of the shell should not contain metal components, and it is best not to design any metal decorative or electroplated parts near the periphery of the shell near the antenna. If necessary, non-metallic processing techniques should be used to achieve this. The conductive spraying on the inner side of the casing should stop at a distance of 20mm from the antenna. For pure metal battery covers, they should be at least 20mm away from the antenna. If a monopole antenna is used, it is prohibited to use metal shells and circular metal decorations on the panel. The distance between the battery (including the electrical connection base) and the antenna should be designed at least 5mm.


Links:Zibo CNC machine tool automatic car washing machine Qingdao refrigeration equipment grinder equipment steel grit fire inspection cabinet sweeper motor desulfurization denitrification equipment drawing mold washing machine automatic soldering machine server repair HART475 hand operator dust-free cloth dust-free paper stack screw type Sludge dehydration machine, precision repair welding machine, Shandong motor repair, rotary hot pot equipment, integrated ultrasonic cleaning machine, Zhongjie radial drilling machine, beer equipment, Shenzhen brass manufacturer, welcome lamp, lens digging, drilling rig, aluminum housing manufacturer, automatic dispensing machine, automatic screwing machine neodymium Iron boron magnet 4g router wireless bridge
We provide you with high quality products
国产好看自拍网| 男女大鸡巴搞鸡抠逼| 丝袜一区二区久久| 亚洲一卡二卡三卡国产| 91无码操逼| 午夜福利国产亚洲| 欧洲二三区| 草亚洲丝袜妈妈| 佐山爱电影一区二区=区| 和静县| 刘玥一区二区在线播放| 色姑娘大香蕉婷婷| 亚洲无吗av在线| 台当局威胁欧阳娜娜等20多名艺人| www.射伊蕉婷婷| 日韩欧美国产另类在线| 被大鸡巴插麻豆视频| 538无码精品视频一区二区三区| 日韩国产又粗又大| 啊啊啊啊,好疼视频| 日本啊啊啊视频| 老熟女亂伦一区二区三区蜜桃视频| 亚洲美女操逼逼逼| 大骚逼影视| 孕妇扣逼毛片视频| 亚洲怡红院一区| 美女被操视频网站在线免费观看| 中文字幕日韩精品视频在线观看四区| 神马久久午夜福利大香蕉| 超碰青青青青操国产精品| av在线一级| 爽妇网亚洲综合| 大鸡巴视频在线91| 久操中文在线| 国产嫩逼AⅤ| 人妻露脸一区二区| 肇庆市| 日逼无码高清视频| 日本高潮少妇一区二区三区| 邹平县| 日韩国产a级片|